Reftekk offers products that promote leak free, reproducible results efficiently and cost-effectively on commercial and residential copper piping systems.
Watch the video below to see why the top contractors are switching to Reftekk.
Reftekk H55 vs Traditional H58 Copper Tubing
Reftekk Bendable Copper Tubing
Available in the following sizes: 1/4”, 3/8”, 1/2”, 5/8”, 3/4”, 7/8”, 1-1/8”, 1-3/8”, and 1-5/8”. All copper tubing options come standard in 19-feet length to fit into 20-foot containers, and the ends are plugged to prevent dirt from getting in the tubes.
Reftekk uses half-hard tubing that meets all U.S. codes and is 14% stronger* than the hard tube offered by other manufacturers.
* Maximum working pressures of ACR Type-L copper tube based on allowable strength shown in ASME B31.5 – 2016, Table 502.3.1
Reftekk's Products Save Time and Money
Digi-Bender is a special tool that makes bending Reftekk piping easy, fast, and accurate right at the job site. The Digi-Bender is user-friendly and with Reftekk's Bend Designer App, all angles and bend designs can be easily programed right on the app to assist in mistake free bending. After that, just pull the trigger and let the machine do the rest.
The Reftekk Digi-Bender can be used to field-bend Soft (O60) and Half-Hard (H55) ACR-L copper tubing and transforms hours of experienced labor into an effortless one-man project. Review the Digi-Bender product page here to learn more.
- Bends the most common ACR type-L copper tube sizes.
- Digi-Bender back former sizes include 5/8" - 1-3/8".
- Easily make accurate bends with Reftekk's Mobile Bending App.
- Eliminate elbow fitting expenses.
- Reduce risks of leaks.
- Significantly reduces pressure drop.
- No over heating due to noticeable visual cue.
- Can be used in swaged sockets and regular fittings.
- Guaranteed full depth penetration.
- Reduces brazing material.
- Fewer leaks.
Reftekk saves up to 75% of the time spent in brazing with products from other manufacturers. Less brazing means a reduction in purging and heat that is applied to the system, leaving you with a much cleaner inside pipe. Review the Brazing Ring product page here to learn more.
- No over heating due to noticeable visual cue.
- Can be used in swaged sockets and regular fittings.
- Guaranteed full depth penetration.
- Reduces brazing material.
- Fewer leaks.
EPDM Insulation
EPDM line sets with 1” and 1-1/2” thickness is required by the IECC codes in nearly all states. EPDM is required on all hot gas lines as it is high temperature closed cell elastomeric foam and will withstand the hot VRF temperatures of 248F. Standard insulation (NBR) will fail at these temperatures. Review the Insulation product page here to learn more.
- Specifically required by several VRF/VRV MFGs.
- Non-Polar, repels moisture
- Available in thickness to meet strict energy codes.
- Exceeds VRF/VRV MFGs 248 degrees Fahrenheit operating temperature requirement
- ASTM E84 (25/50) compliant
- Available on line sets, as well as pre-split, non-split, elbows, and tees.
Cush-A-Therm Supports
The Reftekk Cush-A-Therm is a rigid insulating pipe support that resists compressing or crushing from active-piping system loads. Review the Cush-A-Therm product page here to learn more.
- Proper Tubing Mount
- Fire Response
- Water Vapor Barrier
- UV and Weather Resistant
- Prevents Condensation
- Easy to Install
Refrigerant Ball Valves
Refrigerant Ball Valves for use in VRF/VRV and other refrigerant HVAC applications. Review the Refrigerant Ball Valve product page here to learn more.
- Optional EPDM Insulation Jacket
- Size Range: 1/4" - 1-5/8"
- Accepts Brazing Rings
- Swaged and Straight Valves Available
- Reducers Included
- Built in Schrader Valve
